Little Lumpy 1.5

This is a modified 7.65" LOC Warlock renamed "Little Lumpy". I added 2 layers of 6 oz. glass to air frame, beveled the fins, and did a tip-to-tip with another 2 layers of 6 oz. glass. This was my first attempt at glassing hence the name "little lumpy". It's heavy & slow too!

6/25/17: Update1 - Lil Lumpy needs some TLC - turned into a lawn dart due to my incorrect selection of motor delay. I will rebuild her once I get the pieces apart!

6/25/17: Update 2- Finally got the NC out. Had to cut out bottom of NC and then cut a few slits on NC where it was jammed in. That was enough to relieve the pressure and then I just had to hit it a few times with 2x4. Fins look good. Only about top 3" of airframe are damaged. Looks like I need to order a couple of CR's, NC, some airframe & a coupler. Hava extra MMT and lots of glass!

6/25/17: Update 3 - Lumpy all cleaned up, removed all damaged parts. Now just need to order some stuff!

6/26/17: removed paint from airframe and applied 1 wrap of 6 oz. glass just to reinforce the cracks. Also ordered parts required for repair for LOC Precision. They even threw in the air frame piece needed for free - too bad they didnt do that for the NC - haha!

6/28/17: recieved parts today. Glassed the new tube with 3 layers of 6 oz. Cut coupler, added weight to NC (8 oz.) & started epoxying CR's into airframe. Also did a dry fit. It was cheaper to repair than start over since fins were fine & I already had enough glass for repair

6/30/17: Attached new airframe section to lower section. Sanded/patched/sanded/primed & painted. Once green is cured, I'll tape off fins and paint airframe blue.

7/2/17: painting finished, just waiting on new sticker from Stickershock!

7/4/17: Sticker arrive yesterday. Mark at Stickershock is awesome & very fast. Sticker applied this AM & hit it with a few coats of Clear. Only problem is Lumpy weighs a few pounds more than before so I need a bigger chute!

1/20/18: Suffered CATO. Inside burned pretty bad. Not sure if I will rebuild as attaching new air frame may not be possible. Still looking at options.

1/25/18: Fin can completely undamaged. Cut air frame off just below FWD CR. Easier to attach new air frame. Will use Blue tube this time. Also wanted to replace MMT with Blue tube.

2/16/18: Lil Lumpy complete but a little lumpier! One pound lighter too! New blue tube MMT, new FORE CR, coupled by a few pieces of scrap blue tube I had laying around. Good as new!

10/09/18: Lumpy came in hot last launch & zippered. Been having trouble dialing in delays with this rocket since day 1. Decided to repair zipper and add altimeter bay. Since the zipper was on both sides, had to cut off top 5" of airframe. Might add it back, then again, maybe not. Pics below.

10/10/18: Finished up AV bay. Used an Eggtimer Quantum altimeter, it's WIFI so no switches. Arms thru use of any cell phone. Now just need to repair zipper but waiting on a piece of material. Once zipper fixed, will ground test. More pics below.

10/11/18: Filled zipper with some carbon fiber cloth. Came out OK but just needs to be sanded and then blended & she'll be good as new, again!

10/12/18: Sanded & blended outside of airframe and hit the inside with dremel so NC would fit snug. Prime & paint next!

10/12/18 update #2: primes & painted & ground tested altimeter. 1.5 grams get the laundry out! Unfortunately I used the wrong color paint but I don't care

01/22/19 update: She's as good as new. Cut off split pieces, cut a notch and filled with carbon fiber.

01/23/19 update: added final veil of 3.0 oz. All sanded & ready for some pain